Work Permit Certification (WPR) Questions & Answers

 

This article is about Work Permit Certification Questions. What is Work permit system. Saudi Aramco Work Permit System. Question Answers work permit.  and focusing to the engineers, technicians and supervisors. You will find lot of documents related to this article. Just navigate our website www.paktechpoint.com  and find more articles. Please! Do not forget to subscribe our You tube channel also. Thanks in Advance.

PLEASE SUBSCRIBE OUR PAKTECHPOINT YOUTUBE CHANNEL

Work Permit Certification (WPR) Questions & Answers
1-Who must sign a work permit issuer or receiver certificate?
a-The designated representative.
b-The issuer or receiver.
c-The superintendent of issuer or receiver.
d-The foreman of the issuer or receiver.
2-For how long is a work permit issuer or received certificate valid?
a- 1 year.
b- 6 months.
c- 2 years.
d- 90 days.
3-What are two important reasons for using work permit?
a-To communicate and control work.
b-To track contractors and mange emergencies.
c-To designate representatives and communicate.
d-To track work hours and contractor names.
4-Why do we use work permits in hazardous areas?
a-To identify a designated representative.
b-To identify receivers.
c-To identify hazards and precautions.
d-To check expired
certification.
5-For what conditions are work permits issued?
a-Specific work ar a specific location.
b-General equipment at small work sites.
c-General work at a general location.
d-Specific tools at a general location.
6-What is listed on a work permit?
a-OSHA safety  precautions.
b-Minimum safety precaution.
c-Maximum safety precaution.
d-Government safety precaution.
7-Why do we use the work permit system?
a-To monitor contractor work hours.
b-To renew certificates.
c-To prevent incidents.
d-To log incidents.
8-What does a restricted area require?
a-That extensions are short term.
b-That work permits are issued.
c-That certificates are issued.
d-That receivers respond to emergencies.
9-Whan can a work permit issuer decide that a work permit is not needed in a restricted area?
a-When he decides the work is low risk.
b-When the work is cols work.
c-When a joint site inspection is not needed.
d-Never! They are always required in restricted areas.
10-Select the choice where every item is a restricted area.
a-Pump stations, sewage plants, wells.
b-Wells, loading piers, dining halls.
c-Communications buildings, wells, fenced areas.
d-Wells, office building, welding shops.
11-Examples of low risk work are:
a-Cold work light work and non-destructive testing.
b-Spray painting water-washing and turbine work.
c-Sweeping visual inspecting and minor cleaning.
d-Brush painting, abrasive blasting and sweeping.
12-A specific area is not normally categorized as restricted. Who makes the final decision whether this area should be categorize as restricted?
a-Area superintendent.
b-GI 2.100.
c-Loss prevention.
d-Department Manager
13-Why is a designated representative sometimes used?
a-Too many safety problems were found.
b-The receiver did not come to work.
c-The gas tester found high LEL reading.
d-The issuer may be busy and need help.
14-What are the receivers main responsibilities?
a-Being the designed main representative.
b-Responding to operational emergencies.
c-Filling in for the issuer when the issuer must leave.
d-Complying with safety precautions and signing the permit.
15-An issuer has which responsibilities?
a-Issues and receives work permits.
b-Defines precautions and stands in for the receiver
c-Supervises the work crew and signs the permit.
d-Defines safety precaution and signs the work permit.
16-A receiver must be what?
a-A qualified engineer.
b-A senior contractor manager.
c-A senior craftsman.
d-A designated repersentive.
17-What is a work permit issuer responsible for?
a-Extending
certificates.
b-Nothing once he issues a permit.
c-The receivers action.
d-Equipment or a work area.
18-What can the designated representative do?
a-Accept the receivers responsibilities.
b-Sign the work permit.
c-Inspect the work site.
d-Authorize the receiver to leave.
19-What joint responsibility do issuers and receivers share?
a-Naming the designated representative.
b-Taking gas tests.
c-Doing the work.
d-Safety at the work site.
20-Why is it important that the issuer tell the receiver about safety hazards he may find at a job site?
a-The receiver does not read the work permit.
b-The receiver must respond to emergencies.
c-The receiver may not have worked in the area before.
d-The receiver must take gas test.
21-What two things must the issuer do before issuing a work permit?
a-Close the work permit and check the receivers certificate.
b-Check the recivers certifcate and get countersignatures.
c-Renew certificates and get countersignatures.
d-Provide first aid and assign a fire watch.
22-Who goes on the joint site inspection?
a-The issuer and gas tester.
b-The issuer and the area foreman.
c-The issuer and receiver.
d-The receiver and gas tester.
23-What two things must the receiver do before receiving a work permit?
a-Read the permit and agree to air condition.
b-Take gas tests and check scot air packs.
c-Extend the permit and take gas tests.
d-Train the fire watch and renew the permit.
24-Where must the receiver keep the work permit after it is issued?
a-With a senior crewmember.
b-Dismayed at the jobsite or in his possession.
c-In the control room.
d-Within 75 feet of the work site.
25-When can a receiver leave the job site?
a-When all hot work is stopped.
b-When gas tests read 0.0% LEL.
c-When the issuer has given him permission.
d-Before confined space entry.
Keywords for this article are Work Permit Certification Questions. What is Work permit system. Saudi Aramco Work Permit System. Question Answers work permit. 

26-Who goes a joint site inspection?
a-Designed craftsmen.
b-Issuer and designated representative.
c-Receiver and senior craftsmen.
d-Issuer and receiver.
27-What is a discussed during the joint site inspection?
a-Designated representatives qualifications.
b-GI 2.709 requirement.
c-Check the fire watches certificate.
d-Scope of work and equipment to be used.
28-When would the issuer check to make sure equipment had been property prepared for maintenance work?
a-During the joint site inspection.
b-After getting countersignatures.
c-When the permit is closed.
d-After issuing permit.
29-Why do receivers go on to joint site inspection with the issuer?
a-To start the work.
b-For the receiver to take gas test.
c-To discuss hazards and risks.
d-To check fire watches
certificates.
30-When should a fire watch be assigned?
a-When gas tests are
over 0.0% LEL.
b-For any hot work.
C-Whenever a fire could occur.
d-For high risk jobs.
31-What would the issuer require when welding on in-service hydrocarbon equipment?
a-Fire watch.
b-Fire station.
c-Fire department.
d-Fire blanket.
32-What must the fire watch be?
a-Certified.
b-An issuer.
c-A receiver.
d-Trained.
33-The Fire watch has to know to?
a-Operate fire equipment given to him.
b-Be a receiver.
c-Operate process equipment.
d-Take gas tests.
34-What do we call the person who is required to be at a job site because of a special skill he has?
a-Standby man.
b-Designated representative.
c-Certified.
d-Competent person.
35-A nonflammable material commonly used to purge process equipment is:
a-Nitrite.
b-nitrous oxide.
c-Nitrogen.
d-Nitrate.
36-When preparing equipment for maintenance work the issuer must make sure it is:
a-Isolated, repaired and certified.
b-De-energized with the power turned on.
c-Shut down, isolated and de-energized.
d-Electrified, isolated and shut down.
37-Two common methods of cleaning process equipment include:
a-Water-washing and steaming.
b-Purging and gas testing.
c-Steaming and gas testing.
d-Treating and clarifying.
38-Why do we install blinds in process equipment?
a-To isolate electrical equipment.
b-To prevent blindness.
c-To keep liquids or gases from contacting people.
d-Because it is a government requirement.
39-Equipment is isolated to make sure it cannot be:
a-Slip, trip or fall.
b-Taken to a shop for repairs.
c-Started-up, leak or cause electric shock.
d-shut down by accident.
40-Removing fuses from an electrical circuit or disconnecting electric wiring is an example of what?
a-Purging electrical equipment.
b-Locking electrical equipment.
c-Cleaning electrical equipment.
d-Isolating electrical equipment.
41-Choese two methods of isolating equipment:
a-Shut down and clean.
b-Install locks and take gas tests.
c-Remove piping and install blinds.
d-Install tages and purge.
42-Installing locks and tages on electrical al breakers prevents accidental:
a-Start-up of equipment.
b-Blind instalation.
c-Nitrogeen release.
d-Purging of equipment.
43-Who instaal locks?
a-The foreman and receiver.
b-Every member of the crew.
c-The issuer and gas tester.
d-One member from each work crew.
44-why do we install tags as well as locks?
a-To record gas tests.
b-To record purging cycles.
c-To expalin with the lock is installed.
d-To list safety precaution.
45-What happens to operation locks and tages installed on equipment when operators change shifts?
a-The keys are usually transferred to the new shift.
b-The locks must be replaced.
c-The locks and tags must be removed.
d-The tages must be desroyed.
46-The issuer must try to start-up equipment at the fieid switch after it has been isolated and before work starts to make sure:
a-There is no gas in the area
b-it cannot accidentally start
c-it has been purged and cieaned
d-the receivers tag is installed
47-who should be the first organization to install locks and tags?
a-Operations
b-Receiver
c-Naintenance
d-power distribution
48-Make 8-what must operations do before removing their locks and tags?
a-sure equipment is gas-free
b-make sure equipment can be safely started
c-clean and purge the breaker
d- the gas tests and restart equipment
49-A release of Hazardous Liquids or Gases Permit is required when?
a-Craftsmen build a scaffoid
b-Operators release hydrocarbon to the flare
c-Operators drain equipment
d-Pipe fitters open a line or install blinds
50-Cold work includes?
a-Scaffold building and using a back hoe
b-Brush painting and abrasive blasting
c-abrasive blasting and painting
d-Sand removal and scaffold building
51-covering sewers is required by which work permit?
a-Entry
b-Cold
c-Hot
d-Release
52-The use of an air compressor in an operating area requires which work permit?
a-Entry
b-Cold
c-Release
d-Hot
53-Choose three things you should check before issuing a Release permit
a-Ignition sources ,gloves and safety shoes.
b-Safety hamess , belt and glasses
c-wind direction ,drainage ,ignition sources
d-Sewers, man ways and air mavers
54-what is the difference between hot and cold work?
a-Both use an ignition source
b-Cold uses an ignition source
c-Neither use an ignition source
d-Hot uses an ignition souece
55-what is one hazard with doing hot work?
a-Flash point
b-Ignition source
c-Cold work
d-Vapor pressure
56-Choose three things that are needed before allowing entry into a confined space
a-Gas test ,fire extinguisher ,barricades
b-Lighting ,standby man ,air mover
c-Fire watch ,air mover ,gas tests
d-Air mover , respirator, countersignatures
57-what is the acceptable level of LEL to allow hot work?
a-0.0%
b-10 to 100 ppm
c-5% to 5%
d-21% to 23.5%
58-A release of Hazardous Liquids or Gases Permit is required when?
a-Pipe fitters open a line or install blinds
b-Craftsmen build a scaffold
c-Operators drain equipment
d-Operators release hydrocarbon to the flare
59-Select the statement where ALL THREE items are needed before allowing entry into a confined space?
a-Lighting, standby man ,air mover
b-Gas tests ,fire extinguisher ,barricades
c-Air mover ,respirators, countersignatures
d-Fire watch ,air mover ,gas tests
60-what is considered cold work?
a-Scaffold building and grinding
b-brush painting and abrasive blasting
c-sand removal and scaffold building
d-Abrasive blasting and painting
61-what hazard would you find when doing hot work?
a-ignition point
b-Auto ignition temperature
c-ignition switch
d-ignition source
62-the use of a vehicle in an operating area requires which work permit?
a-cold
b-Entry
c-Release
d-Hot
63-we use work permits in hazardous areas to identity________
a-Expired permits
b-The designated representative
c-Alternate receivers
d-Hazards and precautions
64-The information entered in the “exact work location” box is important because it controls?
a-How many workers can be at the job site
b-where the receiver can work
c-How long receiver can work
d-what equipment the receiver can use
65-what does the duration box tell the receiver?
a-when to go to lunch
b-the expiry date of the receivers certificate
c-How long the extension is approved for
d-when the work must stop
66-why does the issuer need to know what equipment will be used at a job site?
a-it tells him is a fire extinguisher is needed
b-it tells him if a fire watch is needed
c-it helps him identity hazards
d- it tells him if a standby man is needed
67-why is the checklist section important to issuers and receivers?
a-Defines the duration and scope of work
b-Controls the receivers break times
c-it defines all hazards
d-Makes sure important steps have been taken
68-what must the issuer do if a joint site inspection is not done?
a-Require barricades and warning signs
b-Assign a designated representative
c-Tell his foreman
d-write why not on the work permit
69-“Use a fire blanket” or “hand dig only” are examples of what?
a-Hazards
b-Precautionary hazards
c-Additional precautions
d-Regular precautions
70-what must the issuer do if a joint site inspection is not done?
a-Require barricades and warning signs
b-Assign a designated reqresentative
c-Tell his foreman
d-write why not on the work permit
71-what should the issuer do if gas tests are not needed?
a-Use continuous monitoring
b-Write0.0,0 ppm and 21% on the permit
c-Enter “N/A” or” not needed”
d-Sign for the gas tester
72-what information must the gas tester enter on the work permit?
a-LTX-310 expiry date, name and bade number
b-Badge and certificate numbers
c-Gas test results and normal levels
d-Gas test results, name and badge number
73-who can extend a work permit?
a-New unit foreman
b-Designated representative
c-Superintendent
d-New issuer and receiver
74-who can close a work permit?
a-Receiver and standby man
b-issuer and receiver
c-Fire watch
d-issuer and designated representative
75-what must the issuer write on the work permit?
a-Gas test result, name and badge number
b-Name and certificate expiry date
c-Badge number and certificate expiry date
d-Name, organization code and badge number
76-what must the receiver write on the work permit?
a-Name of fire watch, name and badge number
b-Badge number and certificate expiry date
c-Name ,organization code and badge number
d-Name of the Fire watch
77-Where could an issuer find out which permit to issue for a specific job?
a-On the back of any work permit.
b-On the front of any work permit
c-Corporate Loss Prevention Manual
d-Facility operating instructions
78-who must sign a hot work permit to extend it?
a-The new issuer and receiver
b-The new issuer, receiver, and gas tester
c-The new area foreman and the new issuer
d-Superintendents countersignature is required
79-work permits can be issued for up to 30 days if:
a-it is highly unlikely that conditions will change
b-The receiver cannot close the work permit
c-only cold work will be done
d-The work site is far away
80-who is responsible for safety at the work site after a permit has been extended?
a-No one after a permit has been extended
b-The original issuer and receiver
c-The issuer and receiver who signed the extension
d-The old issuer, because he did the Joint Site Inspection
Keywords for this article are Work Permit Certification Questions. What is Work permit system. Saudi Aramco Work Permit System. Question Answers work permit. 

81-what happens if work must continue past the time the original permit was to expire?
a-Work can continue until the job is complete
b-Stop work and come back the next day
c-Keep working ,but tell the issuer
d-Extend the permit or issue a new one
82-If a work permit is not issued during an emergency, what must be done to do the work?
a-All safety precaution must be taken
b-Superintendent must approve
c-Wear Scott Air Pacs
d-Joint site inspection
83-For how long can a work permit NORMALLY be issued and renewed without special agreement?
The answer is in G12.100 paragraph 4.5
a-2consecutive operating shifts(up to a maximum of 24 hours)
b-1conecutive operating shifts(up to a maximum of 12 hours)
c- 2conecutive operating shifts(up to a maximum of 30 days)
d-1conecutive operating shifts(up to a maximum of 30 days)
84-A pipe fitter cannot work on the same piece of equipment using a welders work permit because:
a-Joint site inspections are not needed for pipe fitters
b-welders are usually contractors
c-Each type of work involves different hazards
d-Gas tests are not needed for pipe fitters
85-who must sign a permit issued for up to 30 days?
a-Operations and maintenance division heads
b-Designated representative
c-Receiver and designated representative
d-Operations foreman ,issuer, and receiver
86-The receiver must stop work if:
a-He cannot find the issuer
b-The work site becomes unsafe
c-The issuer leaves the job site
d-The designated representative must leave
87-What would be a good example of when the receiver must stopwork?
a-The backhoe runs out of fuel
b-He cannot read the countersignature.
c-He hears an emergency alarm
d-Materials have not yet arrived
88-The issuer must stop work if:
a-More men were working than stated on the permit.
b-The issuer left the job site
c-The job site was found to be unsafe
d-The issuer lost his copy of the permit
89-what might happen if a safety problem arises and the receiver does not stop work?
a-Countersignatures become void
b-A fire ,injury, or accident
c-His certificate expires
d-The work permit expires
90-what must the receiver do if the stops work?
a-Tell the issuer
b-Tell the designated representative
c-Tell the senior craftsman
d-Tell his immediate supervisor
91-what must the issuer do with the permit after he stops work?
a-Close,then extend the permit
b-Get a countersignature
c-write the reason on the permit
d-Give his copy to the reciever
92-who must sign the work permit to close it? 
a-issuer and receiver
b-Gas tester, issuer, and receiver
c-Designated representative
d-competent person
93-why must work permits be closed?
a-To communicate the status of he work
b-To allow gas tests to be taken
c-To allow the permit to be extended
d-To stop all hot work
94-when must the work permit be closed?
a-After gas tests are taken
b-when the work is finished or the crew leaves
c-when the issuer leaves the work site
d-Before another permit is issued
Please read also: WORK PERMIT SYSTEM COURSE REVIEW QUESTIONS ANSWERS

Keywords for this article are Work Permit Certification Questions. What is Work permit system. Saudi Aramco Work Permit System. Question Answers work permit. 

23 thoughts on “Work Permit Certification (WPR) Questions & Answers”

  1. Hello,
    I’m looking for someone who can arrange Aramco Work Permit Receiver Schedule for me. I’ve got 3rd party certification with me. I’am willing to pay whatever it cost. Thanks.

    Reply
  2. can you send me latest model Saudi Aramco work permit receiver questions and answers key
    my exam is on this month 28 . please

    Reply

Leave a Comment

error: Content is Protected.