JOB SAFETY INSTALLATION JSA FOR ROTATING EQUIPMENT INSTALLATION

Job Steps

Person at Risk

Additional Controls to Reduce Risk

1.2 Extreme hot temperature.
1.3 Poor manual handling techniques.

• Secure appropriate work permit prior to start of work.
• Install barricade tapes provide warning signs on sharp materials to make it visible for all employees present in the work site.
• Provide proper personal protective equipment i.e., hard hat, safety shoes, safety glass and working gloves.
• Personnel in the area should be aware of potential

hazards.

• All heavy equipment Shall be inspected and approved by HSE Department.
• TSTI shall be carried out by the job supervisor emphasizing the hazards identified stated on the permit.• TSTI ensure must be understand by all workers
• Personnel assigned to the tasks shall be experienced workers.

• Improve staggered working  hours. Include substitution of workforce to allow sufficient rest in between employees.
• Provision of cool drinking water and shaded rest

place.

• Supervisor shall monitor their work force by looking for signs of dehydration.
• Maintain proper back posture and body position

during manual lifting of materials. Position body

where less effort is exerted and less strain.

• Use crane, forklift, or manual lifters for heavy loads.
• Divide load weight between co-workers.
• Assign additional person at the trailer bed to assist for

loading/arranging small bore pipe spool.

• Observed proper communication between coworkers

during execution of specified task.

• Personnel in the area should be aware of potential hazards.

• Heavy equipment operators/drivers must undergo competency training and certification before operation/driving heavy equipment.

• All Equipment’s operators shall be certified by Saudi Aramco and record shall be submitted to HSE Department for approval.

• Personnel in the area should be aware of potential hazards.

• Equipment should have blinker light/sound. 

• Provide PWAS to equipment.

2.3 Improper handling of material resulting injury or health risks

• Provide an approved lifting plan prior to lifting. Observed  existing structure on the swing radius of crane.
• Conduct daily and visual inspection to all rigging hardware and crane parts prior to lifting.
• Routine check for the competency of riggers.
• Personnel in the area should be aware of potential hazards.
• Equipment shall be lifted and supported only at the designed lifting eye.
• Ensure load was placed steady and securely on the

back of the trailer truck. Use of sling to hold off the load

will be advised.

• Handle all material with care and arranged properly
• Ensure equipment will be inspected by HSE Department and set properly.
• Use appropriate hand, face, feet, and body protection equipment.
• Static Equipment material to be kept in proper place.
• Ensure all material kept out to prevent unnecessary tripping hazard.

Installation setting and alignment of Rotating Equipment.

3.6 Improper installation of Rotating equipment

• Conduct daily and visual inspection to all rigging hardware and crane parts prior to lifting.

• Secure load by competent rigger and use appropriate rigging tackles with visible SWL and has 3rd party certified.

• Inspect rigging tackles before each use for wear & tear and make sure has color code for the current month.

• Observed double choked for long load to prevent slips and use tag lines to properly hold a nd control the load.

• Test lift prior to lifting avoid lifting a load that exceeds the capacity of the crane and over reaching of load.

• Avoid swinging of loads on a high speed manner. Use tag lines to control loads.

• Any personnel are not allowed to ride on a load.

• Crane’s swinging radius must be barricaded. Install warning signs Danger Lifting in progress.

• Use proper personal protective equipment (PPE) like gloves, Safety Glass, safety shoes & Hard hats.

• Provide fully physical

warning signs on the barricade and corresponding equipment to avoid unauthorized entry.

• Ensure shall be use material bags secured with structure or scaffolding platform to avoid falling material from height.

• Provide caution tape, hard barricade around the working area for to control unauthorized persons.

• Full body Harness shall be strictly required when working at height and 100+ tie off. • Tools shall be secured with retaining strings, Secure equipment on a permanent

• Use proper personal protective equipment (PPE) like gloves, safety glass, safety shoes & Hard hats.

• Personnel in the area should be aware of potential  hazards.

• Rotating equipment 

Installation areas shall be barricaded and secured.

Only authorized personnel shall be permitted inside the barricaded area. Warning signs “DANGER ROTATING EQUIPMENT INSTALLATION ON PROGRESS- KEEP AWAY” shall be in place.

• Competent technician will be perform Rotating Equipment installation activity.

• equipment installation in strictly accordance with manufacturer’s instructions.

• Equipment shall not be left unattended at any time during the work.

• Equipment designed for a fixed location shall be securely anchored to prevent moving.
• Equipment guarding shall be provided to protect the operator and other employees in the area from rotating hazards.
• Keep hands, hair and loose clothing clear from all moving parts.
• Workers assigned on  elevated area with a height of 1.8m. (6 ft) or greater shall be equipped with an inspected and color coded full body harness.
• Full body Harness shall be strictly required when working at height and 100+ tie off.
• Keep body parts out of pinch points. Use required proper personal protective equipment.