Repair Procedure for Adsorbent tower annular chamber weld pinhole
1. SCOPE This procedure covers repair work for Adsorbent towers (Vessel, Towers etc.) pinhole on weld joints on annular chamber, which may occurred during…
Read articleMECHANICAL
Browse 253 free articles, standards and practical guides about MECHANICAL.
253 articles in this topic
METHOD STATEMENT FOR WELD REPAIR PROCEDURE FOR VESSEL INTERNAL
1. PURPOSE. 2. DEFINITION. 3. MANPOWER. 4.TOOLS AND EQUIPMENT. 5. GENERAL. 6. ASSESMENT OF THE INDICATION. 7. REMOVAL OF DEFECT (UNACCEPTABLE INDICATIONS). 8.WELD-BUILD UP.…
Read articleMODIFICATION OF SUPPORT OF PIPELINE (OUT OF CENTER SHOE)
1.0 PURPOSE 2.0 SCOPE 3.0 APPLICABLE DOCUMENTS 4.0 RESPONSIBILITY 5.0 MANPOWER 6.0 TOOLS & EQUIPMENT 7.0 METHODS/PROCEDURES 8.0 QUALITY CONTROL 9.0 SAFETY PRECAUTION 10.…
Read articleAdvertisement
METHOD STATEMENT INSTALLATION OF FURNACE AIR PRE HEATER
1.0 PURPOSE 2.0 SCOPE 3.0 APPLICABLE DOCUMENTS 4.0 RESPONSIBILITY 5.0 MANPOWER 6.0 TOOLS & EQUIPMENT 7.0 METHODS/PROCEDURES 8.0 QUALITY CONTROL 9.0 SAFETY PRECAUTION 10.0…
Read articleAIR PREHEATER INSTALLATION, OPERATION & MAINTENANCE MANUAL
1. INSTALLATION MANUAL 1.1 Introduction. 1.2 Storage. 1.3 Foundation and Support Structure. 1.4 Installation Procedure. 1.5 Field Insulation. 2. OPERATION MANUAL 2.1 Introduction. 2.2…
Read articleBOLT TIGHTENING PROCEDURE AND METHOD STATEMENT
This article is about Bolt tightening, torquing and tensioning procedure and method statement for structural steel works. Here explained sequence wise of bolt tightening.
Read articleOn Stream Inspection of Piping Procedure | Method of Statement
This method of statement or procedure will be applied for the baseline thickness survey (BLS) conducted during the EPC phase by CONTRACTOR for a…
Read articleULTRASONIC THICKNESS MEASUREMENT BY PULSE ECHO METHOD
This procedure establishes the requirements for manual ultrasonic thickness determination of base materials in plates, pipes, tanks, vessels, tubings, castings and forgings using the…
Read articleMETHOD OF STATEMENT FOR SUPPORT MODIFICATION(SHORT STOOL)
1. PURPOSE 2.SCOPE 3. REFERENCES 4. RESPONSIBILITIES 5. MAN POWER 6. TOOLS AND EQUIPMENT 7. METHODS I REPAIR PROCEDURES 8. QUALITY CONTROL 9. SAFETY…
Read articleMODIFICATION THREADED JOINT PROCEDURE (UNDER GROUND VENT PIPE)
1. PURPOSE 2. SCOPE. 3. REFERENCES. 4. RESPONSIBILITIES. 5. MAN POWER. 6. TOOLS AND EQUIPMENT. 7. MODIFICATION PROCEDURES. 8. QUALITY CONTROL. 9. SAFETY PRECAUTION.…
Read articleINSTALLATION OF CATALYST LIFT LINE | METHOD STATEMENT
1.0 PURPOSE 2.0 SCOPE 3.0 APPLICABLE DOCUMENTS 4.0 RESPONSIBILITY 5.0 MANPOWER 6.0 TOOLS & EQUIPMENT 7.0 METHODS/PROCEDURE 8.0 QUALITY CONTROL 9.0 SAFETY PRECAUTION 10.0…
Read articleREPAIR OF UNSUCCESSFUL SECOND WELD REPAIR PROCEDURE
1.0 PURPOSE 2.0 SCOPE 3.0 APPLICABLE DOCUMENTS 4.0 RESPONSIBLITIES 5.0 TOOLS AND EQUIPMENTS 6.0 METHOD/PROCEDURES 7.0 QUALITY CONTROL 8.0 SAFETY PRECAUTIONS 9.0 ATTACHMENT REPAIR…
Read article